内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

先进战斗机过失速机动大气数据融合估计方法

可控的过失速机动是先进战斗机超机动性能的重要标志，飞机飞行包线的扩大已超出传统的大气数据系统测量范围，可靠的迎角、侧滑角、总压、静压等飞行大气数据是制约先进战斗机过失速机动中飞行控制的关键因素。以中国推力矢量验证机为对象，基于过失速机动飞行试验的数据，开展大气参数估计与验证研究。结合过失速机动的时间与空间特性，研究了基于风速、地速、空速矢量和惯性姿态、导航参数的大气参数融合计算方法；针对过失速大迎角状态下飞机周围气流非定常、模型非线性导致的融合大气参数误差的复杂特性，进一步构建深度神经网络，对机动状态融合迎角、侧滑角的强非线性误差进行拟合。仿真和飞行试验表明：该方法可在大迎角飞行状态下实现主要大气参数的融合估计，过失速机动过程中融合迎角误差优于2.3°，融合得到的大气参数可为过失速大迎角机动飞行控制提供可靠的大气参数状态反馈。     

Optimization of bits allocation and path planning with trajectory constraint in UAV-enabled mobile edge computing system

In this paper, an Unmanned Aerial Vehicle (UAV) enabled Mobile Edge Computing (MEC) system is studied, in which UAV acts as server to offer computing offloading service to the Mobile Users (MUs) with limited computing capability and energy budget. We aim to minimize the total energy consumption of MUs by jointly optimizing the bit allocation for uplink, computing at the UAV and downlink, along with the UAV trajectory in a unified framework. To this end, a trajectory constraint model is employed to avoid sudden changes of velocity and acceleration during flying. Due to high-order information in use, we lead to a more reasonable nonconvex optimization problem than prior arts. An Alternating Direction Method of Multipliers (ADMM) method is introduced to solve the optimization problem, which is decomposed into a set of easy sub-problems, to meet the requirement on the efficiency in edge computing. Numerical results demonstrate that our approach leads a smoother UAV trajectory, significantly save the energy consumption for UAV during flying.     

酚醛树脂基纳米多孔材料的制备及结构调控

酚醛树脂基纳米多孔材料（Phenolic Resin-based Nanoporous Materials，PNM）是满足新一代航天飞行器轻质、高效隔热需求的新型热防护材料，传统制备方法中需使用超临界干燥技术，制备周期长、成本高。本研究通过两步法，即先合成线性酚醛树脂，再进行溶胶-凝胶的方法，实现了常压干燥PNM的制备。系统研究了固化剂含量、固化温度和固化时间对材料结构的影响和调控作用，分析了影响材料收缩率和热稳定性的因素。结果表明，PNM的微观纳米结构的变化会影响材料干燥后的收缩率，制备大颗粒、大孔径的微观结构更有利于降低材料的收缩率。而PNM的热稳定性主要受交联反应过程形成的化学结构的影响，通过优化固化剂的含量可提高PNM的热稳定性。当固化剂含量为10%，固化温度提高至150℃，固化时间延长至48 h的条件下，获得的PNM有最高的热稳定性（900℃下的残碳率为54.2%）、最发达的孔结构（比表面积为264.0 m²/g、孔容为2.67 cm³/g、平均孔径为40.0 nm）和最小的收缩率（0%）。此PNM制备方法简单、性能优异，在未来航天飞行器上有广阔的应用前景。     

差分卫星定位技术及其在武器系统中的应用

差分卫星定位系统可以极大地提高卫星定位的精度,但也有使用、维护复杂等缺点。针对差分卫星定位的特性,首先阐述了卫星差分定位的基本原理,分析了卫星定位误差源,并介绍了差分定位系统对各种误差的修正情况,然后介绍了差分定位系统的分类、方法及发展,其中详细介绍了在武器系统领域中应用较广的局域差分系统的各种方法及其优缺点;最后,对差分系统的实际应用进行了阐述,并重点探讨了其在进攻性武器及防御性武器领域实现应用的可行性。     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

高速加工的发展及其关键技术

介绍了高速加工技术的特点及发展，并重点介绍了高速主轴单元、高速加工进给系统、高速切削刀具材料等关键技术。     

燃气的基准表及图制定

本文在阐述基准的热力学概念基础上,提出了燃气基准的计算方法,应用CHAPPELL推荐的有关燃气热力性质表达式,导出计算燃气基准的公式,通过微机计算,将结果整理成燃气基准的有关表、图。     

Stellar infrared astronomy with EDISON

In this review the IR emission from circumstellar material is discussed, both of ionized gas and dust grains, and the astrophysical information that can be extracted from such observations. Some emphasis is placed on the possibilities of stellar IR astronomy using a large space-borne telescope, especially with respect to the much better spatial and spectral resolution of such a telescope compared to the current generation of ground-based and space IR telescopes.